Pella Window 807X0101 User Manual

© 2012 Pella Corporation  
Part Number: 807X0101  
WINDOW REPLACEMENT INSTRUCTIONS FOR  
CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS  
USING FRAME SCREWS  
These instructions were tested and developed for replacing windows in wood-frame wall construction systems designed  
to manage moisture. Installation recommendations for other types of wall construction, wall systems, conditions, multiple  
windows or bow bay windows, may be obtained from Pella Corporation or a local Pella retailer. Building designs, construction  
methods, building materials, and site conditions unique to your project may require an installation method different from these  
instructions and additional care on your part. Determining the appropriate installation method is the responsibility of you, your  
architect, or other construction professional.  
Note: This instruction is not for use in applications that have vinyl, steel or aluminum siding where water may be behind the  
siding above the window. In these applications, the siding may need to be removed and window installed using the new  
construction installation instruction that is attached to the window.  
YOU WILL NEED TO SUPPLY:  
TOOLS REQUIRED:  
Řꢀ7DSHꢀPHDVXUH  
Řꢀ/HYHO  
Řꢀ&HGDUꢀRUꢀ,PSHUYLRXVꢀVKLPVꢁVSDFHUVꢀꢂꢃꢄꢀWRꢀꢄꢅꢆ  
Řꢀ&ORVHGꢀFHOOꢀIRDPꢀEDFNHUꢀURGꢁVHDODQWꢀEDFNHUꢀꢂꢃꢄꢀWRꢀꢇꢅꢀIWꢈꢆ  
Řꢀ3HOODpꢀ6PDUW)ODVKŠꢀIRLOꢀEDFNHGꢀEXW\OꢀZLQGRZꢀDQGꢀGRRUꢀ  
flashing tape or equivalent  
Řꢀ6TXDUH  
Řꢀ+DPPHU  
Řꢀ3HOODꢀ:LQGRZꢀDQGꢀ'RRUꢀ,QVWDOODWLRQꢀ6HDODQWꢀRUꢀHTXLYDOHQWꢀ  
KLJKꢀTXDOLW\ꢉꢀPXOWLꢊSXUSRVHꢀVHDODQWꢀꢂꢃꢀWXEHꢀSHUꢀZLQGRZꢆ  
Řꢀ/RZꢀH[SDQVLRQꢉꢀORZꢀSUHVVXUHꢀSRO\XUHWKDQHꢀLQVXODWLQJꢀ  
window and door foam sealant.  
SEALANT  
Řꢀ6FUHZGULYHUVꢀꢀ  
ꢂꢋꢄꢀ3KLOOLSVꢀDQGꢀ)ODWꢀEODGHꢆ  
Řꢀꢋꢃꢅꢀ7RU[ꢀGULYHUꢀELW  
Řꢀ'ULOO  
'2ꢀ127ꢀXVHꢀKLJKꢀSUHVVXUHꢀRUꢀODWH[ꢀIRDPV  
Řꢀꢋꢌꢀ[ꢀꢇꢊꢃꢁꢌŔꢀ)LQLVKꢀKHDGꢀVFUHZV  
ŘꢀꢃꢁꢌꢍꢀELW  
Installation will require two or more people for safety reasons.  
REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.  
Always read the Pella®  
Limited Warranty before purchasing  
or installing Pella products. By  
installing this product, you are  
acknowledging that this Limited  
Warranty is part of the terms of  
the sale. Failure to comply with all  
Pella installation and maintenance  
instructions may void your Pella  
product warranty. See Limited  
Warranty for complete details at  
Flashing tape #1  
Flashing tape #2  
#8 x 3-1/8"  
Finish head screw  
 
Window Preparation (continued):  
2
B. Double-Hung and Clad Frame:ꢀ2QꢀWKHꢀURRPꢀVLGHꢀRIꢀWKHꢀZLQGRZꢉꢀGULOOꢀꢃꢁꢌꢍꢀGLDPHWHUꢀFOHDUDQFHꢀKROHVꢀWKURXJKꢀWKHꢀIUDPHꢀDWꢀ  
WKHꢀORFDWLRQVꢀVKRZQꢈꢀ6SDFHꢀWKHꢀKROHVꢀDꢀPD[LPXPꢀRIꢀꢏꢍꢀIURPꢀHDFKꢀHQGꢀDQGꢀDꢀPD[LPXPꢀRIꢀꢃꢏꢍꢀRQꢀFHQWHUꢈꢀ  
Note: The lower sash must be raised to drill the holes in the sill of the double-hung window.  
Designer Series®  
and Pella® ProLine  
Architect Series®  
Double-Hung Head  
Double-Hung Head  
1/2"  
Drill 1/8"  
clearance hole  
Drill 1/8"  
clearance hole  
Clad Frame Head  
1"  
Double-Hung Jamb  
Double-Hung Jamb  
Drill 1/8"  
clearance hole  
Drill 1/8"  
clearance hole  
1/4"  
Drill 1/8"  
clearance hole  
Drill 1/8"  
clearance hole  
1"  
Drill 1/8"  
clearance hole  
Drill 1/8"  
clearance hole  
1/2"  
Clad Frame Sill  
Double-Hung Sill  
Double-Hung Sill  
Setting and Fastening the Window:  
3
A. Slide the window into the opening, placing the bottom of the window on the spacers at the bottom of the opening.  
3RVLWLRQꢀWKHꢀZLQGRZꢀVRꢀWKDWꢀWKHꢀH[WHULRUꢀIDFHꢀRIꢀWKHꢀIUDPHꢀH[WHQGVꢀDꢀPLQLPXPꢀRIꢀꢇꢁꢎꢍꢀRQWRꢀWKHꢀH[WHULRUꢀZDOOꢀPDWHULDOꢀWRꢀ  
DOORZꢀIRUꢀWKHꢀDSSOLFDWLRQꢀRIꢀEDFNHUꢀURGꢀDQGꢀVHDODQWꢀꢂ6HHꢀLOOXVWUDWLRQVꢀLQꢀ6WHSꢀꢎꢀIRUꢀVHDODQWꢀGHWDLOVꢆꢈꢀ&HQWHUꢀWKHꢀZLQGRZꢀ  
EHWZHHQꢀWKHꢀVLGHVꢀRIꢀWKHꢀRSHQLQJꢀWRꢀDOORZꢀFOHDUDQFHꢀIRUꢀVKLPPLQJꢉꢀDQGꢀLQVHUWꢀRQHꢀꢋꢌꢀ[ꢀꢇꢊꢃꢁꢌꢍꢀŵQLVKꢀKHDGꢀVFUHZꢀLQWRꢀHDFKꢀ  
of the top clearance holes. This will hold the window in place while shimming it plumb and square.  
B. Place shims 1" from the bottom and top of the window between  
the window and the sides of the opening and at the midpoint of the  
ZLQGRZꢀVLGHꢈꢀ.HHSꢀVKLPVꢀEDFNꢀꢃꢁꢄꢍꢀIURPꢀLQWHULRUꢀIDFHꢀRIꢀZLQGRZꢈꢀ  
ꢇ%  
Adjust the shims as required to plumb and square the window in the  
opening. Also shim behind all the pre-drilled clearance holes.  
Note: Do not shim above the window or in the space between the  
spacers at the bottom of the window. DO NOT over shim.  
 
Setting and Fastening the Window (continued):  
3
C. Fasten the window to the opening.ꢀ)LQLVKꢀQDLOLQJꢀWKHꢀLQWHULRUꢀWULPꢀWRꢀZDOOꢀWKHQꢀGULYHꢀꢋꢌꢀ[ꢀꢇꢊꢃꢁꢌꢍꢀŵQLVKꢀKHDGꢀVFUHZVꢀLQWRꢀ  
each of the pre-drilled clearance holes.  
Designer Series®  
and Pella® ProLine  
Architect Series®  
Double-Hung Head  
Double-Hung Head  
1/2"  
#8 x 3-1/8"  
finish head  
screw  
#8 x 3-1/8"  
finish head screw  
Double-Hung Jamb  
Double-Hung Jamb  
Casement Head/Jamb  
Clad Frame Head/Sill/Jamb  
1"  
#8 x 3-1/8"  
finish head  
screw  
#8 x 3-1/8"  
finish head  
screw  
#8 x 3-1/8"  
finish head screw  
#8 x 3-1/8"  
finish head screw  
1/4"  
#8 x 3-1/8"  
finish head  
screw  
#8 x 3-1/8"  
finish head screw  
#8 x 3-1/8"  
finish head screw  
1/2"  
Double-Hung Sill  
Double-Hung Sill  
Casement Sill  
D. Check window operation (vent units only).  
Architect Series® and Designer Series® Double-Hung: Cut the checkrail bands and remove the shipping spacers. Open  
and close the window a few times to check for proper operation. Make sure the window will tilt correctly. Close and lock  
the window.  
ProLine® Double-Hung:ꢀ7RꢀUHPRYHꢀVLGHꢀVSDFHUVꢉꢀVOLGHꢀWKHPꢀXSꢀWRꢀDSSUR[LPDWHO\ꢀꢎꢍꢀDERYHꢀWKHꢀERWWRPꢀVDVKꢈꢀ/LIWꢀWKHꢀ  
FOLSꢀE\ꢀWKHꢀLQWHULRUꢀOHJꢀDQGꢀURWDWHꢀXSZDUGꢀWRꢀUHPRYHꢈꢀ5DLVHꢀWKHꢀERWWRPꢀVDVKꢀDSSUR[LPDWHO\ꢀꢄꢍꢉꢀDQGꢀWLOWꢀWKHꢀVDVKꢀLQꢀE\ꢀ  
depressing the jamb liner and pulling inward on the top corners of the sash. Remove the sash clips and return the sash  
to its original position.  
Casement: Unlock the window by lifting up on the lock handle. Turn the crank to open the window. Remove the shipping  
spacers from between the sash and window frame. Close and lock the window.  
Note: If there are any problems with the operation of the window, recheck shim locations and adjust for plumb and  
square.  
 
Sealing the Window to the Exterior Wall Cladding:  
:KHQꢀDSSO\LQJꢀVLGLQJꢉꢀEULFNꢀYHQHHUꢀRUꢀRWKHUꢀH[WHULRUꢀŵQLVKꢀPDWHULDOꢉꢀOHDYHꢀDGHTXDWHꢀVSDFHꢀEHWZHHQꢀWKHꢀZLQGRZꢀIUDPHꢀDQGꢀ  
the material for sealant. Refer to the illustration corresponding to your finish material.  
Note: The sealant details shown are standard recommendations from the sealant industry. Contact your sealant supplier  
for recommendations and instructions for these and any other applications.  
4
WOOD SIDING  
WITH TRIM  
BRICK VENEER  
WOOD  
SIDING  
Backer Rod and  
Sealant typical  
Sealant typical  
Sealant typical  
3/8" Clearance  
3/8" Clearance  
Accessory Groove  
Insulate  
and  
seal per  
Step 5  
Insulate  
and  
seal per  
Step 5  
1/8" Clearance  
Accessory  
Groove  
Insulate  
and  
seal per  
Step 5  
Accessory Groove  
Perimeter Sealant  
must extend to room  
side of Accessory  
Groove.  
Perimeter Sealant  
must extend to room  
side of Accessory  
Groove.  
3/8"  
3/8"  
1/8"  
1/2"  
Min.  
1/2"  
Min.  
A. Insert backer rod into the space around the window as deep as it will go.  
7KLVꢀVKRXOGꢀSURYLGHꢀDWꢀOHDVWꢀDꢀꢃꢁꢄꢍꢀFOHDUDQFHꢀEHWZHHQꢀWKHꢀEDFNHUꢀURGꢀDQGꢀWKHꢀ  
H[WHULRUꢀIDFHꢀRIꢀWKHꢀZLQGRZꢈ  
ꢎ$  
Note: Backer rod adds shape and depth for the sealant line.  
B. Apply a bead of high quality exterior grade sealant to the entire perimeter  
of the window.  
ꢎ%  
C. Shape, tool and clean excess sealant. When finished, the sealant should be  
the shape of an hourglass.  
Note: This method creates a more flexible sealant line capable of expanding  
and contracting.  
Interior Seal:  
5
Caution: Ensure use of low pressure polyurethane window and door installation foams and strictly follow the foam  
manufacturer’s recommendations for application. Use of high pressure foams or improper application of the foam may  
cause the window to bow and hinder operation.  
A. Apply insulating foam sealant. From the interior, insert the nozzle of the applicator  
5A  
DSSUR[LPDWHO\ꢀꢃꢍꢀGHHSꢀLQWRꢀWKHꢀVSDFHꢀEHWZHHQꢀWKHꢀZLQGRZꢀDQGꢀWKHꢀURXJKꢀRSHQLQJꢀ  
DQGꢀDSSO\ꢀDꢀꢃꢍꢀGHHSꢀEHDGꢀRIꢀIRDPꢈꢀ7KLVꢀZLOOꢀDOORZꢀURRPꢀIRUꢀH[SDQVLRQꢀRIꢀWKHꢀIRDPꢀDQGꢀ  
will minimize squeeze out. Apply sealant across interior surface of shims to create a  
FRQWLQXRXVꢀVHDOꢈꢀ)RUꢀZLQGRZVꢀZLWKꢀMDPEꢀH[WHQVLRQVꢀLQVWDOOHGꢉꢀHQVXUHꢀWKHꢀIRDPꢀLVꢀSODFHGꢀ  
EHWZHHQꢀWKHꢀZLQGRZꢀIUDPHꢀDQGꢀWKHꢀURXJKꢀRSHQLQJꢉꢀQRWꢀEHWZHHQꢀWKHꢀMDPEꢀH[WHQVLRQꢀ  
and the rough opening. Follow foam manufacturer's instructions.  
Note: It may be necessary to squeeze the end of the tube with pliers to be able to insert  
into the space between the window frame and the rough opening. DO NOT completely fill  
the space from the back of the backer rod to the interior face of the opening.  
B. Check window operation (vent units only) by opening and closing the window.  
Note: If the window does not operate correctly, check to make sure it is still plumb, level, square and that the sides are not  
bowed. If adjustments are required, remove the foam with a serrated knife. Adjust the shims, and reapply the insulating  
foam sealant.  
 
Interior Finishing:  
6
Visible wood surfaces of Pella® products must be finished. Failure to do so voids the Limited Warranty. If products cannot  
be finished immediately, cover with clear plastic film to protect from dirt, damage and moisture. Remove any construction  
residue before finishing. Sand all wood surfaces lightly with 180 grit or finer sandpaper. DO NOT use steel wool. BE  
&$5()8/ꢀ127ꢀ72ꢀ6&5$7&+ꢀ7+(ꢀ*/$66ꢈꢀ5HPRYHꢀVDQGLQJꢀGXVWꢈ  
Note: To maintain proper product performance do not paint, finish or remove the weather-stripping, mohair dust pads,  
gaskets or vinyl parts. Air and water leakage will result if these parts are removed. If paint, stain or finish gets on the mohair  
weather-stripping, immediately blot it thoroughly with a rag and allow it to dry. Flake off any remaining residue. After  
finishing, allow windows to dry completely before closing them.  
Pella Corporation is not responsible for finishing imperfections. Use of inappropriate finishes, solvents, brickwash or  
cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited Warranty.  
EXTERIOR FINISH  
7KHꢀH[WHULRUꢀIUDPHꢀDQGꢀVDVKꢀDUHꢀSURWHFWHGꢀE\ꢀDOXPLQXPꢀFODGGLQJꢀZLWKꢀRXUꢀWRXJKꢀ(QGXUD&ODGpꢀRUꢀ(QGXUD&ODGꢀ3OXVꢀEDNHGꢊ  
on factory finish that needs no painting. Clean this surface with mild soap and water. Stubborn stains and deposits may be  
removed with mineral spirits. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.  
Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse reactions with window and door  
materials and voids the Limited Warranty.  
CARE AND MAINTENANCE  
Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s manual by  
IMPORTANT NOTICE  
Because all construction must anticipate some water infiltration, it is important that the wall system be designed and  
constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages caused by  
anticipated and unanticipated water infiltration; deficiencies in building design, construction and maintenance; failure to  
install Pella® products in accordance with Pella installation instructions; or the use of Pella products in wall systems which  
do not allow for proper management of moisture within the wall systems. The determination of the suitability of all building  
components, including the use of Pella products, as well as the design and installation of flashing and sealing systems are  
the responsibility of the Buyer or User, the architect, contractor, installer, or other construction professional and are not the  
responsibility of Pella.  
Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the  
ZDOOꢀV\VWHPVꢉꢀVXFKꢀDVꢀEDUULHUꢀ([WHULRUꢀ,QVXODWLRQꢀDQGꢀ)LQLVKꢀ6\VWHPVꢉꢀꢂ(,)6ꢆꢀꢂDOVRꢀNQRZQꢀDVꢀV\QWKHWLFꢀVWXFFRꢆꢀRUꢀRWKHUꢀQRQꢊ  
ZDWHUꢀPDQDJHGꢀV\VWHPVꢈꢀ([FHSWꢀLQꢀWKHꢀVWDWHVꢀRIꢀ&DOLIRUQLDꢉꢀ1HZꢀ0H[LFRꢉꢀ$UL]RQDꢉꢀ1HYDGDꢉꢀ8WDKꢉꢀDQGꢀ&RORUDGRꢉꢀPella makes  
no warranty of any kind and assumes no responsibility for Pella windows and doors installed in barrier wall systems. In  
the states listed above, the installation of Pella products in barrier wall or similar systems must be in accordance with Pella  
installation instructions.  
Product modifications that are not approved by Pella Corporation will void the Limited Warranty.  
 
INSTALLING ROTO COVER AND CRANK  
Note: Finish the interior of the window and allow the window to dry before proceeding with these instructions. (To open  
the window for finishing, partially insert the lock handle into the jamb, unlock the unit, temporarily attach the crank handle  
and turn to open.)  
A. Place the cover over the operator stud and snap into  
Pocket End  
B
place. Position the pocket end of the cover into place.  
Note: If the cover does not have the screw hole, apply  
pressure on the pocket end of the cover to snap the cover  
into place and proceed to step C.  
Screw Hole  
Operator Stud  
B. Insert the provided screw into the hole in the bottom  
of the pocket. 8VHꢀDꢀꢋꢀꢃꢀ3KLOOLSVꢀVFUHZGULYHUꢀWRꢀVHFXUHꢀ  
the pocket screw snug against the bottom of the  
pocket to avoid scratching the crank handle knob. DO  
NOT over tighten.  
A
Crank Handle  
D
Knob  
E
Operator Stud  
C. Use a medium size flat-blade screwdriver to loosen  
the set screw in the crank handle.  
D. Slide the crank handle onto the stud. Unlock, open  
Set Screw  
C
window, then close and lock window.  
Pocket  
E. Fold the crank handle down and check alignment of  
knob with the pocket.  
Note: You may need to adjust the crank position on the  
stud until the correct alignment is achieved.  
F. Open the crank and tighten the set screw.  
*ꢈꢀAfter the final installation, fold the crank over and snap the knob into the pocket.  
Note: Even with the window open the crank can be folded to avoid interferring with the window treatments.  
CASEMENT WINDOW LOCK LEVER REMOVAL AND INSERTION  
Note: You may want to remove the lock lever prior to finishing the window,  
or if it needs to be replaced with a lock lever in a different finish.  
C
Interior  
Exterior  
B
A. Unlock and open the window.  
B. Place the lock lever in the locked position.  
C. From the exterior of the window, insert a small flat-blade screwdriver  
between the cam and lock lever near the bottom of the opening  
between the stop and frame gasket.  
D. Push the screwdriver inwards with a small amount of pressure; then turn  
the blade slightly clockwise for a left hand unit, counter-clockwise for a  
right hand unit. DO NOT over-twist the screwdriver, this can damage the  
lock driver.  
Exterior  
E
F
Interior  
Note: This will release the hook in the lever from the cam hook.  
D
E. Remove the lock lever by pulling it toward the interior of the building.  
F. To install a lock lever, hold it in the lock position and insert it, from the  
interior, into the slot until it snaps into the cam.  
© 2012 Pella Corporation  
Part Number: 807X0101  
 

Philips Appliance Trim Kit SJM2003 User Manual
Philips Cell Phone Accessories M888 User Manual
Philips Computer Monitor 107X User Manual
Philips Home Theater System HTS3270 User Manual
Plinius Audio Stereo Amplifier Hiato User Manual
Polaris Offroad Vehicle Sportsman S User Manual
Porter Cable Drill 90538674 User Manual
Powerware Power Supply UPS20 30kVA User Manual
ProForm Home Gym PFAW75072 User Manual
ProForm Treadmill 831291770 User Manual